Video Transmitters
Lumenier has a wide variety of FPV video transmitters with a range of output power. Each video transmitter is small in size and provides a high quality FPV video feed back on the ground. Shop for all Lumenier video transmitters here.
Lumenier TX5GS 25-200-500mW 5.8GHz FPV Transmitter w/ BFCMS Control (MMCX)
The Lumenier TX5GS 25-200-500mW 5.8GHz FPV Video Transmitter w/ BFCMS Control is the perfect all around FPV VTX. This transmitter features the latest in VTX technology allowing you to fully operate Frequency and Power settings via your Radio Controller or BetaFlight OSD. No more needing to reach into your drone to manually change channels, just do it from the comfort of your chair (Manual button control is also there if you need it). This transmitter is enabled with adjustable power settings as well, from 25mW all the way to 500mW. So whether you're at a race or flying long range, the TX5GS has you covered.
The TX5GS includes a 5v output to power FPV cameras and a stand alone audio pin to transmit sound to your receiver. It also uses the robust MMCX style antenna connector. This connection is much stronger compared to the U.FL style, allowing you to connect / disconnect hundreds of times without the worry of it wearing out. The Lumenier AXII Antenna with MMCX connector is the perfect match to the TX5GS.
The TX5GS features easy to use buttons with LED interface to manually change bands, channels, and power output. It also has easy to solder to pads for the connections, so no more worrying about breaking a small connector in a crash. All this is packed into a 36*22*6.5mm sized transmitter weighing only 5g! This transmitter is capable of outputting a lot of power, so mount it in an area where it will have good air flow.
-
Specifications
- Input voltage: 7~27V(2~6S LiPo)
- 32 Channels: (US Legal) A/E/F/R Band
- Output Power: 25, 200, 500mW switchable
- BEC Output: 5V/1A redundancy for Camera or FC
- Traditional Button +LED control of frequency and power
- BFCMS (BFOSD & LUA Script) control via FC UART _TX (Use Tramp Protocal in BF)
- Power Consumption: 3.1W Max. @ 500mW
- Video Input Impedance: 75 Ohm
- Audio Subcarrier Frequency: 6.5 MHz
- RF Connector: MMCX
- Video Format: NTSC/PAL
- Stackable or Double side tape mountable
- Firmware upgradeable
- Weight: 5g (Tx only, w/o SMA cable)
- Size: 36*22*6.5mm w/30.5mm mounting
Includes
- 1 x Lumenier TX5GS
- 1 x MMCX to SMA Pigtail Extension Cable RG178 cable 9cm
- Clear PVC Heat-Shrink Tubing
- (Antenna not included)
-
Features
- Small and Lightweight
- Stackable on standard 30.5x30.5 FC mounting holes
- BFCMS controls via BetaFlight & LUA Script (similar to Smart Audio)
- Adjustable Power 25-200-500mW
- Wide Input Voltage with 5v output for Camera
- Solid MMCX antenna connection
LUX Mini 20x20 5.8GHz FPV Video Transmitter (25-800mW)
The Lumenier LUX Mini brings high-powered video transmission into a tiny 20x20 package. The LUX Mini is a 5.8GHz VTX with five adjustable levels of transmitting power: PIT/25/200/500/800 mW. The side of the VTX has an easy-to-see row of LEDs for quick band and channel visibility so you always know where you are transmitting.
In addition to the incredible power output in such a small package the LUX Mini VTX has "Smart Audio" included, allowing you to remotely change settings on the VTX like power output, frequency and more via Betaflight OSD controls. The entire board is also conformal coated for added protection during operation.
The LUX Mini Video Transmitter comes with a full set of mounting hardware, MMCX whip antenna and high quality silicone wire to solder to. The white plastic case acts as a protective cover to the VTX, and also reduces the mounting hole size from M3 to M2. This gives you 2 different ways to mount it with either full size M3 screws, or micro sized M2 screws. This video transmitter works perfectly on both micro and full sized builds!
And of course, it comes in white to match all your other LUX gear!
-
Specifications
- Input Voltage: 7-36V DC
- Output Voltage: 5V 1A
- @12V Input Current: 40mA@Pitmode, 95mA@25mW, 185mA@200mW, 250mA@500mW, 380mA@800mW
- Channels: 48CH including RaceBand
- Power: PIT/25/200/500/800 mW
- Installation Hole: M3, (M2 with plastic cover) 20*20mm
- Dimensions: 28*28*3.3 mm
- Weight: 4.46g(without cover), 5.4g(with cover)
Includes
- 1 x LUX Mini VTX
- 1 x Protective Cover
- 1 x MMCX Dipole Antenna
- 1 x Wire Set
- 1 x Hardware Set
-
Features
- Compact 20x20 stackable design
- Variable power from 25mW to 800mW + Pit Mode
- Mounts with M3 or M2 hardware
- Conformal coated for added protection
- Licensed Smart Audio from TBS
- Optional protective cover included
Lumenier TX5G Pro Series of Mini 25mW, 200mW, 600mW 5.8GHz FPV Transmitter with Power Switch
The Lumenier TX5GPro Mini 200mW 5.8GHz 32CH FPV video transmitter is the perfect VTX for FPV racing. The new Pro series of transmitters feature a RF toggle switch, meaning you can power on your aircraft without broadcasting your FPV signal. Now you can get the benefit of an easy to use press button transmitter combined with the peace of mind that you won't interfere with other FPV signals when powering on your aircraft while on the ground! To start the RF transmission simply power your TX and then press and hold the function button for 2 seconds. A green LED will indicate that the TX transmitter is actively broadcasting. In addition the Pro series includes a new and upgraded on-board 5v regulator. This new regulator can handle the high current spikes generated by newer ESCs that have aggressive braking enabled.
Lumenier TX5G R Series of Mini 25mW, 200mW, 600mW 5.8GHz FPV Transmitter with Raceband
The Lumenier TX5G6R Mini 600mW 5.8GHz 32CH FPV video transmitter is the perfect VTX for long range FPV, and FPV racing where you need the extra power! The high output 600mW transmission power means longer range and better signal penetration compared with lower power transmitters. The TX5G6R has 32 channels including the new Raceband frequencies. Our friends from ImmersionRC first divided the 5.8 band into 8 channels evenly spread out 37MHz from each other, which allows more racers flying at the same time on the same band. Lumenier Raceband transmitters are fully compatible with FatShark and ImmersionRC receivers. The Tx includes a 5v output to power FPV cameras and an on-board microphone to transmit audio to your receiver.
