Legacy

Brushless Gimbals

Brushless Gimbals

This 2-Axis brushless gimbal unit enables you to equip your stock QAV400 with a brushless gimbal to shoot breathtaking gimbal stabilized aerial footage. This gimbal unit quickly attaches to the QAV400 in about 20 seconds and can be removed again just as easily. Now you can fly an acrobatic flight with your QAV400 and a fully gimbal stabilized flight all within the same session.


LayerLens for GoPro 1 and 2

LayerLens for GoPro 1 and 2

The orginal LayerLens made for the GoPro 1 and 2. This LayerLens is built on the same principals as the newer LayerLens for GoPro 3, by protecting only the lens it provides a great reduction in overall weight compared with the stock GoPro case.You will be required to take out the glass lens from a GoPro case or purchase a GoPro Lens Replacement Kit separately. Assembly required. LayerLens does not obstruct the Microphone or the USB, A/V, or back extension plugs. It fits the old and new Hero2 versions of the GoPro.

LayerLens for GoPro 3 and 4

LayerLens for GoPro 3 and 4

This is the newest revision of LayerLens for the GoPro 3

LayerLens for the GoPro 3 & 4 camera series features a hard and anti-reflective ("AR") coated lens with an anti-smudge coating on the viewing side. AR coating is applied to both sides of the lens which ensures low external and internal lens reflections.

  • This new design features an injection-molded uni-body lens holder that is light and tough.
  • Ships with 1 high quality lens. The lens is a 2mm thick, photo grade, hardened, anti-reflective and smudge coated cast acrylic lens.
  • None of the video or photo modes show the bezel.
  • Fits all GoPro 3 and 4 models
  • Upgrade the lens to a Circular Polarized Lens to cut down on glare and reflections.


The Carbon Fiber QAV250

The Carbon Fiber QAV250

The Lumenier QAV250 is also available in full 3k Carbon Fiber. The Lumenier QAV250 Mini FPV Quadcopter Carbon Fiber Edition airframe has all the features of the standard QAV250 plus the added benefits of carbon fiber. The pure 3K carbon fiber material gives the airframe incredible strength while at the same time reducing the overall weight. The entire assembled kit weighs in at only 122g. The QAV250 is a symmetric 250mm size airframe that accommodates 5" props. The 250mm is measured motor shaft to motor shaft diagonally.


  • Tuning Settings for the QAV250 with a CC3D

    These are good starting parameters for flying the QAV250 with a CC3D. This set-up assumes FX-2206 2000kv motors, a 3s lipo, 5x3 Gemfan props, and 12amp SimonK ESCs.

    These settings are based off of Juz's CC3D settings.

The G10 QAV250®

The G10 QAV250®

The Lumenier QAV250 Mini FPV Quadcopter airframe. With small yet fully functional FPV quadcopters having gained a lot of popularity recently, we decided to design a small FPV airframe that deserves the QAV label. The QAV250 is a symmetric 250mm size airframe that accommodates 5" props. The 250mm is measured motor shaft to motor shaft diagonally. Our airframe was designed to support a 3s lipo setup and powerful 2206 2000kv motors - Lumenier FX-2206-13 2000kv


  • Specifications
    • Airframe Weight: 170g (with PDB, LED boards, landing gear and hardware)
    • AUW: The QAV250 is flown with an AUW of around 540g (includes all flight electronics, FPV gear and Mobius HD camera).
  • Features
    • A 2.5D CNC-ed G10 unibody main frame board
    • Integrated power distribution board for ESCs and FPV flight electronics
    • 2 integrated LED strips (white and red) to aid LOS orientation
    • Easy Lipo Access (suggested Lipo is a Lumenier 3s 1300mah)
    • Support for 32mm board cams as well as cams in cases with mounting bracket
    • Support for HD camera (such as the Mobius)
    • Integrated and included Landing Gear reminiscent of the QAV500 CF Landing Gear
  • Vibration Free Video

    Like all QAV airframes, the QAV250 produces vibration and jello free HD recordings. We achieve this vibration free performance without the use of Lumenier's clean/dirty frame separation that is utilized in larger QAV airframes such as the QAV400, QAV500, and QAV540G. This simplifies the small QAV250 airframe, making it lighter, reduces parts count, and failure points. We will soon release flight videos flown by our Team of Lumenier pilots.

    Suggested Build Parts

    Helpful Links
QAV250 "Fury" Power Distribution Board

QAV250 "Fury" Power Distribution Board

Looking for a QAV250 Power Distribution Board (PDB) to get an integrated FPV setup and simple R/C wiring? This board, nicknamed "FURY", provides upgraded power distribution with current sensing, filtered power to the A/V equipment and option to install a TBS CORE module, while also adding rigidity to the airframe.

The ESCs are soldered to the the board (all wires), making the board layout very tidy and modular. It is designed with the OpenPilot flight controller in mind, requiring only two cables to install the flight system and another two cables (included) to finish the FPV system.


QAV250 Vibration Damping Camera Plate

QAV250 Vibration Damping Camera Plate

The vibration damping camera plate will help elimate any vibrations coming from your QAV250 before they get to your camera. The soft silicon bobbins separate the camera plate from the airframe while at the same time absorbing any vibrations. The camera plate takes advantage of the QAV250's top plate's slots allowing you to slide the plate forward or back 18mm. By mounting the camera plate all the way forward you can mount a GoPro camera without any props or frame in view, even in 1080p wide mode.

The vibration damping camera plates are available in 2 different materials, G10 and Carbon Fiber.


QAV250 Prop Guards

QAV250 Prop Guards

The QAV250 prop guards will help avoid crashes due to light prop strikes. Instead of the propellor brushing a wall or obstacle the prop guard will strike first, guarding your props and possibly avoiding a costly crash. This prop guard will work on V1 of the QAV250 if using motors that use M3 motor mounting screws. On V2 of the QAV250, this prop guard can also work for motors such RCX motors that use M2 mounting screws.

The prop guards are available in 2 different materials, G10 and Carbon Fiber.


The Lumenier QAV250 FPV Backpack

The Lumenier QAV250 FPV Backpack

The Lumenier QAV250 backpack allows you to take your QAV250 plus all your FPV gear anwhere you go! It features 16 total compartments which provides a wide range of storage options, and each one is sized for a specific use. The backpack has a customized foam insert to protect your QAV250 (extensions included) along with your transmitter and all your FPV gear.


The Professional Travel Case for the QAV250

The Professional Travel Case for the QAV250

The Professional Travel Case is customized specifically for the QAV250 and accessories. Injection-Molded out of ultra high-strength polypropylene copolymer resin, the case has watertight and dust-proof properties; its submersible design is resistant to corrosion and impact damage. Features a molded-in hinge, strong latch system, snap-down rubber over-molded grip handle, and automatic purge valve. It is resistant to UV, solvents, corrosion, fungus and impact damage.


The QAV250 Aero Guard

The QAV250 Aero Guard

The new Lumenier Aero Guard increases your speed by reducing drag in an elegant way. The Aero Guard is a single, laser-cut part fabricated from rip resistant material that slides over the QAV250's aluminum spacers. In addition to improving aerodynamics the Aero Guard also protects the airframe's electronics.

  • Weight: 4g
  • Material: Tear resistant plastic
  • Color: Black


QAV250 Angled Motor Mount Extensions

QAV250 Angled Motor Mount Extensions

These aluminum motor mounts extend the arms of the QAV250 enabling mounting of 6" props while also tilting the motors to a 10 degree angle all in a single part. This angled motor mount extension facilitates the QAV250 to fly at a lower angle of attack when angled-motor-mount-close-set-4 performing fast forward flight ("FFF") thereby reducing drag, increasing speed, and keeping cameras more level. The part is light, strong, and machined out of a single piece. The mount attaches to any stock QAV250 airframe with 4 screws. No nuts required. The motor attaches to the angled mount as usual. Patent Pending.


Lumenier Workstation

Lumenier Workstation

This is the Lumenier Workstation, your all-in-one RC stand and parts organizer. The Workstation is a flexible and modular RC work stand with an organizing parts base.

The Lumenier Workstation is precisely machined out of high quality aluminum in the USA. The base plate starts as a solid piece of black anodized aluminum and is CNC machined into a grooved parts organizer base. The center aluminum stand is 7" tall and features a 360 degree ball pan/tilt, allowing you to move your model to any desired angle and hold it in place. The top plate has hundreds of threaded holes allowing you to position the included posts and adjustable clamps in many formations to fit your model exactly.

The Workstation works great as a extra set of hands to hold whatever part you're working on in the exact position you need it to be. Perfect for RC builds, soldering, general assembly and disassembly. It also doubles as a beautiful display stand. Show off your models at events and make your friends jealous!


  • Specifications
    • Features high quality machined aluminum
    • Base Plate Dimensions: W 12" x L 9" x H 0.25"
    • Top Plate Dimensions: W 9" x L 5" x H 0.375"
    • Center Post: W 1.5" x H 7" with Ball Head Pivot Mount
    • Weight: 4.5lbs
    Includes
    • 1x Base
    • 1x Center Post
    • 1x Top Plate
    • 2x Short Locating Posts
    • 2x Spring Loaded and Adjustable Locating Posts
    • 1x Allen Key for Locating Posts
The Blast

The Blast

The Blast is a 450 size carbon quadcopter…that shoots harmless projectiles 50+ feet on a flat trajectory! The Blast shoots soft Nerf disks powered by a high RPM brushless motor. The Nerf disks are deadly accurate at distance while remaining utterly harmless at point blank. A servo shoots disks out of a 13 disk magazine. The airframe, shooting mechanism, servo, firing motor and dedicated ESC are all included in the kit, as well as a Lumenier 4Power mini PDB. The Blast brings a whole new dimension to multirotors, making dogfighting and target practice possible. Build one with a buddy and re-enact the Battle of Britain at your local airfield!

The Danaus Quadcopter

The Danaus Quadcopter

Inspired by the popular QAV250, the Lumenier Danaus is a mini FPV quadcopter with integrated prop protection. The frame is constructed from 2 large unibody frame plates utilizing a Carbon Fiber with Glass Fiber laminate. Like the QAV250, the Lumenier Danaus features a power distribution board and a FPV board camera mounting plate. Equipped with a 5" inch prop and a 3s or 4s power train, the Danaus makes for a great trainer or obstacle course flyer.

CAGE Code: 84VM0
Copyright © 2023 Lumenier. All Rights Reserved.
NOTION Design Group