Flight Controllers

Lumenier LUX V2

Lumenier LUX V2

The Lumenier LUX V2 flight controller is the next generation of the popular Lumenier LUX. It uses a powerful F3 processor along with top of the line hardware. Unleash the capabilities of your FPV Racing Quadcopter with the Lumenier LUX Flight Controller. Achieve gyro refresh rates up to 8kHz (high speed SPI) using popular Betaflight, CleanFlight and RaceFlight firmware along with ultra low looptimes. The LUX comes with BetaFlight pre-installed.

The LUX V2 builds on all the best features of the V1 board and further improves on hardware components and layout. Now you get a whopping 5x dedicated UART ports for periphials, along with an SD Card slot for practically unlimited data logging. The MPU has also been updated to the low noise MPU6000 Gyro making tuning even easier. No longer do you need to solder jumper pads for PPM/SBUS selection, it is automatically chosen via software! The powerful F3 MCU also supports the latest DSHOT protocol available in the newest BetaFlight firmware.

The Lumenier LUX is a very low profile board allowing it to be mounted in a variety of ways. The board also comes with a set of pin headers you can optionally solder on. Alternatively, signal wires can be soldered directly to the pads to save on size and weight. The LUX supports PPM or Serial RX (including Futaba, FrSky, S.BUS, DSMX). A signal inverter is already included for S.BUS. Please note: PWM input for individual channels is not supported.


  • Specifications
    • STM32F303 RCT6(256kB flash) 32-bit processor
    • MPU6000 SPI Gyro/Accelerometer
    • Micro SD memory card slot (SD card not included)
    • High quality, gold plated PCB
    • Highest quality components, individually sourced to meet Lumenier standards
    • Micro USB connector for programming
    • Dimensions: 36x36x6mm (includes USB in height)
    • Mounting Holes: 30.5mm square to center of holes
    • Weight: 5g
    • Included: 1x Lumenier Lux V2 Flight Controller & 2x 2x7 Straight Pin Headers
  • Features
    • Dedicated UART for RC RX use, no need to solder a jumper to select PPM/SRX anymore.
    • Dedicated telemetry UART, this brings the total to 5x plus USB.
    • SD Card slot for BlackBox data recording (SD card not included)
    • Low noise MPU6000 SPI Gyro.
    • USB detection can disable things like buzzer when configuring on the bench.
    • New ultra low noise regulators for MCU and IMU power systems.
    • USB Conflict resolution - Hardware inversion, SBUS or telemetry can be used on any of the 3 available hardware serial ports. USB will not interfere with peripherals.
    • High Speed SPI 8kHz Gyro
    • MPU interrupt connected to F3, allowing the F3 to know immediately when fresh data is available.
    • Dedicated Boot button for easy firmware flashing.
    • Reinforced solder pads for trouble-free direct soldering.
    • Extremely low profile design.
    • Recessed, sideways pin headers. Also enables soldering of all wires directly to pads without use of any pin headers.
    • Integrated FRSky RSSI Filter (RC filter).
    • Input voltage 6v to 24v. Power the board directly from flight pack up to 6S (on 'BAT' pad only!).
    • VIN + VBAT merged - A single wire to power the board will provide voltage input and Telemetry/OSD voltage data.
    • Filtered voltage output - output 5v 1A (and 3.3v where applicable) to power peripherals such as GPS, RX, BLACKBOX, OSD. 5v/3.3v RX selectable.
    • Note: RX pad is dedicated to UART 4 in the Configurator.
    • Betaflight support (Supports new DSHOT protocol)
    • Cleanflight support (RACE target).
    • BLHeli passthrough flashing supported by hardware
    • Raceflight ready
Lumenier F4 AIO Flight Controller

Lumenier F4 AIO Flight Controller

The Lumenier F4 AIO Flight Controller combines a STM32F4 MCU, Betaflight OSD, full PDB, 12v 3A and 5v 3A BEC, Current Sensor, all in 1 compact package and weighing only 10g! Like other Betaflight OSD enabled flight controllers, you’ll be able to tune your PID’s using your transmitter and use the drag and drop OSD setup in the OSD tab of the BetaFlight Configurator.


  • Specifications
    • Mounting holes: 30.5 x 30.5mm
    • Target: LUXF4OSD in BF 3.2+
    • Firmware: Betaflight
    • Weight:10g
    • Includes: 1x Lumenier F4 AIO Flight Controller, 1x XT60 flat mount power connector & 1x Set of nylon spacers (5mm and 3mm), screws and nuts
  • Features
    • STM32F4 MCU (Spi connected to Gyro)
    • Built in PDB for direct connect of ESC power and signal wires
    • Built in high current bar
    • Direct battery connect 3-6S with filtered Output of 5v 3A, 12v 3A
    • SBUS/PPM + DSMX Ports
    • SPI Gyro MPU6000
    • On-Board Drag and Drop OSD (controlled by BetaFlight, FC over SPI bus)
    • Onboard SD Memory for Blackbox
    • Built-in Current Sensor (~140A)
    • 3x UART
    • Buzzer output
    • WS2812B LED output
Lumenier SKITZO Flight Controller Powered by RaceFlight

Lumenier SKITZO Flight Controller Powered by RaceFlight

The Lumenier SKITZO Flight Controller Powered by RaceFlight is the most advanced, performance driven, flight controller ever designed. The SKITZO Flight Controller was created in collaboration with and named after the flow master himself SKITZO FPV. Capable of running 32kHz gyro sample rate, PID loop, motor loop and processing all calculations in real time. The SKITZO FC is powered by the same hardware as the new RaceFlight Revolt which has incredible performance. The Lumenier SKITZO Flight Controller uses a F405 MPU and a Invensense 20602 gyro in combination with RaceFlight software to give you the BEST performance possible. This gyro is by far the most noise free and accurate gyro available.


Lumenier MICRO LUX V2 - F4 Flight Controller + OSD

Lumenier MICRO LUX V2 - F4 Flight Controller + OSD

The Lumenier MICRO LUX V2 F4 Flight Controller with OSD brings incredible power and performance to the micro brushless world. It uses a powerful F4 processor along with top of the line hardware. Now you can get all the performance from an F4 based flight controller in a micro size! The V2 now includes an on-board Betaflight OSD. Using an On Screen Display has never been simpler, just drag and drop in the Betaflight Configurator. This flight controller uses 20x20mm mounting holes and a low profile design allowing for smaller airframe designs than ever before. The MICRO LUX V2 comes with BetaFlight pre-installed.

The MICRO LUX supports both SBUS and PPM inputs as well as DSM/DSMX receivers with both 5v and 3.3v support.

Lumenier™ and LUX™ are registered trademarks of Lumenier.


  • Specifications
    • STM32F405 (2MB flash) 32-bit processor
    • MPU6000 Gyro/Accelerometer
    • High quality 1.6mm PCB
    • Micro USB connector for programming
    • Dimensions: 27x27x6mm (includes USB in height)
    • Mounting Holes: 20mm square to center of holes
    • Weight: 4g
    • Includes: 1x Lumenier MICRO Lux V2 F4 Flight Controller w/ OSD & 1x Set of plastic 5mm and 3mm standoffs + screws / nuts
  • Features
    • 2-4S Direct Lipo input support (5-16v)
    • On-board BetaFlight OSD
    • On-board 5v/2A and 3.3v/0.2A regulators
    • SBUS and PPM support
    • RGB LED dedicated pad, Current Sensor pad and Buzzer Pad
    • VBAT Monitoring support
    • 3x UART Ports
    • Betaflight support (Supports new DSHOT protocol)
    • BLHeli passthrough flashing supported by hardware
  • Optional Recommendations

    We suggest the following gear to complete your micro brushless build. (Not included)

    Lumenier Mini BLHeli_S 12A 4-in-1 OPTO ESC DSHOT

    Helpful Links
LUX Mini 20x20 5.8GHz FPV Video Transmitter (25-800mW)

LUX Mini 20x20 5.8GHz FPV Video Transmitter (25-800mW)

The Lumenier LUX Mini brings high-powered video transmission into a tiny 20x20 package. The LUX Mini is a 5.8GHz VTX with five adjustable levels of transmitting power: PIT/25/200/500/800 mW. The side of the VTX has an easy-to-see row of LEDs for quick band and channel visibility so you always know where you are transmitting.

In addition to the incredible power output in such a small package the LUX Mini VTX has "Smart Audio" included, allowing you to remotely change settings on the VTX like power output, frequency and more via Betaflight OSD controls. The entire board is also conformal coated for added protection during operation.

The LUX Mini Video Transmitter comes with a full set of mounting hardware, MMCX whip antenna and high quality silicone wire to solder to. The white plastic case acts as a protective cover to the VTX, and also reduces the mounting hole size from M3 to M2. This gives you 2 different ways to mount it with either full size M3 screws, or micro sized M2 screws. This video transmitter works perfectly on both micro and full sized builds!

And of course, it comes in white to match all your other LUX gear!


  • Specifications
    • Input Voltage: 7-36V DC
    • Output Voltage: 5V 1A
    • @12V Input Current: 40mA@Pitmode, 95mA@25mW, 185mA@200mW, 250mA@500mW, 380mA@800mW
    • Channels: 48CH including RaceBand
    • Power: PIT/25/200/500/800 mW
    • Installation Hole: M3, (M2 with plastic cover) 20*20mm
    • Dimensions: 28*28*3.3 mm
    • Weight: 4.46g(without cover), 5.4g(with cover)
    Includes
    • 1 x LUX Mini VTX
    • 1 x Protective Cover
    • 1 x MMCX Dipole Antenna
    • 1 x Wire Set
    • 1 x Hardware Set
  • Features
    • Compact 20x20 stackable design
    • Variable power from 25mW to 800mW + Pit Mode
    • Mounts with M3 or M2 hardware
    • Conformal coated for added protection
    • Licensed Smart Audio from TBS
    • Optional protective cover included
Lumenier LUX F7 Ultimate Flight Controller (Dual Gyros)

Lumenier LUX F7 Ultimate Flight Controller (Dual Gyros)

The Lumenier LUX F7 flight controller is full of features including dual gyros, barometer, OSD, 5x UART, SD Card slot, easy soldering layout and much more.

The Lumenier LUX F7 Ultimate Flight Controller is the next generation of the popular Lumenier LUX flight controller lineup. It uses a powerful F7 processor along with top of the line hardware. Unleash the capabilities of your FPV Racing Quadcopter with the Lumenier LUX F7 Flight Controller. The LUX F7 comes with 2 onboard gyros allowing you to choose the perfect settings for your setup. The default gyro is the tried and true MPU6000, capable of 8k/8k with high resistance to vibration noise. Alternatively enable the ICM20602 to achieve gyro refresh rates up to 32kHz.

The LUX F7 builds on all the best features of its V2 predecessor and further improves on hardware components and layout. You get a whopping 5x dedicated UART ports with built-in inversion for peripherals, along with an SD Card slot for practically unlimited data logging. Now with an integrated BetaFlight OSD, it makes it super simple to display important information on your FPV display like battery voltage, flight time, warnings, RSSI, smart audio features and more.

The features don't stop there! The LUX F7 has the ability to run 2 camera signals, with a built switching ability. This means you can run 2 cameras simultaneously and assign a switch via the PINIO feature in Betaflight to alternate between the 2 feeds at the flip of a switch.

Have you ever been in an FPV race where you need to plug in your quad, but you don't want to broadcast an FPV signal to knock your friends out of the air? Or how about you crash, and need to save your VTX from burning up while baking in the hot sun. With the LUX F7 you can remotely turn your VTX on or off via a switch on your radio! The LUX features an on-board 1A VBAT filtered power pad designed to power your VTX. Using the PINIO resource, you can assign this pad to a switch on your radio, remotely controlling the power source to your video transmitter.

Long range quad and FPV plane pilots will also love the Lumenier LUX F7. It has all the features you need to take full advantage of the long range and autonomous flight technology. The LUX F7 has an on-board barometer, buzzer pad, I2C pad, iNAV support, GPS/compass pads, and up to 8 PWM inputs S1-S8 for a ton of servo and motor control.

The Lumenier LUX F7 is a very low profile board allowing it to be mounted in a variety of ways. Signal wires can be soldered directly to the pads to save on size and weight. The LUX supports PPM or Serial RX (including FrSky, S.BUS, DSMX, etc.).


  • Specifications
    • High quality, gold plated PCB
    • Micro USB connector for programming
    • Dimensions: 36x36x6mm (includes USB in height)
    • Mounting Holes: 30.5mm square to center of holes
    • Weight: 6g
    Includes
    • 1x Lumenier LUX F7 Ultimate Flight Controller
    • 6x Anti-vibration silicone grommets (for M3 sized screws)
    • 1x 8pin micro JST-SH 5cm connector, 1x 6pin connector
  • Features
    • MCU: 216MHz STM32F722RET6
    • IMU: MPU6000 & ICM20602, Dual Gyros built-in
    • Baro: BMP280
    • OSD: AT7456E
    • Blackbox: MicroSD card slot
    • Anti-Vibration silicone grommets built in
    • 5x Uarts (1,2,3,4,6) with built-in inversion
    • 1x Softserial supported
    • 8x Dshot/Proshot/oneshot outputs
    • 1x I2C
    • 1x SH1.0_8pin connector (Vbat/G/Curr/R6/S1/S2/S3/S4)
    • Vbat filtered output power for VTX, switchable via AUX (modes tab-user1)
    • Dual Camera image switchable via AUX (modes tab-user2)
    • Camera control
    • WS2812 Led Strip support
    • Beeper solder pad
    • RSSI solder pad
    • INAV analog airspeed
    • Input: 6~36V (2~8S LiPo)
    • BEC: 5V 2A cont. (Max.3A)
    • LDO 3.3V: Max.200mA
    • Current Sensor: No
    • Battery Voltage Sensor: 1:10
LUX MINI F7 Flight Controller

LUX MINI F7 Flight Controller

The Lumenier LUX MINI F7 Flight Controller is a powerful, fully featured FC in a tiny 20x20 package.

The Lumenier LUX MINI F7 Ultimate Flight Controller is the next generation of the popular Lumenier LUX flight controller lineup. It uses a powerful F7 processor along with top of the line hardware. Unleash the capabilities of your FPV Racing Quadcopter with the Lumenier LUX MINI F7 Flight Controller. This MINI LUX F7 comes in a small 20x20 form factor weighin only 5g! Don't let the size of this flight controller fool you though, it is fully feature packed and works great on both micro and full sized drones.

The MINI LUX F7 builds on all the best features of its predecessors and further improves on hardware components and layout. You get a whopping 6x dedicated UART ports with built-in inversion for peripherals, along with built in 128Mbit 16MB flash memory for Blackbox recording. It includes an integrated BetaFlight OSD, making it super simple to show important information on your FPV display like battery voltage, flight time, warnings, RSSI, smart audio features and more.

Have you ever been in an FPV race where you need to plug in your quad, but you don't want to broadcast an FPV signal to knock your friends out of the air? Or how about you crash, and need to save your VTX from burning up while baking in the hot sun. With the LUX F7 you can remotely turn your VTX on or off via a switch on your radio! The LUX MINI F7 features an on-board LC VBAT filtered power pad designed to power your VTX. In addition it has an onboard 5v 3A regulator to power camera, Rx, and LEDs all at the same time. Using the PINIO resource, you can assign this pad to a switch on your radio, remotely controlling the power source to your video transmitter.

The Lumenier LUX MINI F7 supports all the popular accessories like beeer, camera control, smart audio / tramp VTX control, PWM outputs, and I2C connection.


  • Specifications
    • High quality, gold plated PCB
    • Micro USB connector for programming
    • Dimensions: 28x28x6mm (includes USB in height)
    • Mounting Holes: 20mm square to center of holes
    • Weight: 5g
    Includes
    • 1x Lumenier LUX MINI F7 Ultimate Flight Controller
    • 4x Anti-vibration silicone grommets (for M3 sized screws)
    • 1x 8pin micro JST-SH 7cm connector for 4in1 ESC
    • 1x set of mounting hardware
    • 4x M3x25mm black oxide steel screws
    • 4x M3x22mm black oxide steel screws
    • 4x M3x5mm plastic spacer
    • 4x M3x3mm plastic spacer
    • 4x M3 rubber o-rings
    • 8x M3 plastic hex nuts
  • Features
    • MCU: 216MHz STM32F722RET6
    • IMU: ICM20602
    • OSD: AB7456
    • Blackbox: 128Mbit / 16MByte
    • Anti-Vibration silicone grommets built in
    • 6x Uarts with built-in inversion
    • 1x Softserial supported
    • 1x I2C
    • 1x SH1.0_8pin connector (Vbat/G/Curr/TLM/S1/S2/S3/S4)
    • Vbat filtered output power for VTX
    • Camera control
    • Smartaudio & Tramp VTX protocol support
    • WS2812 Led Strip support
    • Beeper solder pad
    • Input: 6~36V (2~8S LiPo)
    • BEC: 5V 3A cont.
    • LDO 3.3V: Max.200mA
CAGE Code: 84VM0
Copyright © 2019 Lumenier. All Rights Reserved.
NOTION Design Group