Brushless ESC

 Lumenier Mini Razor Pro 4in1 20x20 F3 BLHeli_32 45A 2-6s ESC

Lumenier Mini Razor Pro 4in1 20x20 F3 BLHeli_32 45A 2-6s ESC

The Lumenier Mini Razor F3 BLHeli_32 45A 2-6s ESC is a 32bit ESC running the latest gen. BLHeli_32 firmware, and featuring a future proof powerful F3 processors. Now 4 of these ESCs combine to have more processing power than your whole flight controller! The 32bit architecture enables the ESC to run at incredible speeds resulting in better performance, faster input signals and lower latency compared to older 8bit ESCs. This ESC also features a live telemetry connection for more advanced flight controllers, as well as a top of the line current sensor.

The Mini Razor Pro was designed for the drone pilot who loves the tiny 20x20 form factor but also wants to squeeze out every ounce of juice out of their equipment as possible. While the entire ESC is wider than the mounting holes, many frames have extra spillover space on the sides, so the additional width isn't an issue. Using this ESC allows you to still use your favorite 20x20 F7 FC while not worrying about putting too much stress on a lower-rated ESC. The Mini Razor Pro has 45A of continuous support that will give you the peace of mind to push your quad to the limit!

The Mini Razor Pro's innovative modular power system gives the user the option to install one of three different modules that give the 4-in-1 ESC additional functionality related to power management. Choose either the power filter module, extra capacitance module, or voltage regulator module to make your Mini Razor Pro fit to your specific needs (modules sold separately).


  • Specifications
    • Input: 2-6s LiPoly
    • Constant: 45 Amps
    • Burst: 60 Amps
    • Dimensions: 33x46x5mm
    • Mounting holes: 20x20 M3
    • Signal wire: 7cm
    • Weight: 12.5g
    • 8pin connector pinout: VBAT, Ground, Current ADC, TLM, Motor 1, Motor 2, Motor 3, Motor 4
    Includes
    • 1x Lumenier Mini Razor 4in1 20x20 F3 BLHeli_32 45A 2-6s ESC
    • 1x 8pin micro JST-SH 7cm connector for 4in1 ESC to FC connection
    • 4x M3 Rubber o-rings
    • 4x M3 Anti-vibration gummies
  • Features
    • New F3 MCU running at 108MHz, (older ESCs use F0 at 48MHz)
    • Latest Gen. firmware using BLHeli_32 (Razor_32 target)
    • Supports DSHOT 1200, Proshot, Oneshot125 (125-250us), Oneshot42(41.7-83.3us) and Multishot (5-25us). Auto-detection.
    • Modular Power System for even further customization (modules sold separately)
    • Oversized motor pads for easy installation and maintenance
    • Adaptive timing, compatible with a wide range of motors and Kv
    • Synchronous rectification technology adds efficiency, damped light
    • Powerful regenerative braking / active braking.
    • 2-6s LiPo battery compatible
 Lumenier Razor LED 55A 4-in-1 F3 BLHeli_32 2-6s ESC

Lumenier Razor LED 55A 4-in-1 F3 BLHeli_32 2-6s ESC

The Lumenier Razor LED 55A 4in1 F3 BLHeli_32 2-6s ESC is a 32bit ESC running the latest gen. BLHeli_32 firmware, and featuring future proof powerful F3 processors. Now 4 of these ESCs combine to have more processing power than your whole flight controller! The 32bit architecture enables the ESC to run at incredible speeds resulting in better performance, faster input signals and lower latency compared to older 8bit ESCs. This ESC also features a live telemetry connection for more advanced flight controllers, as well as a top of the line current sensor.

The Lumenier Razor LED ESC also includes 4x onboard RGB LEDs with a pre-programmed controller chip with an easy-press button. Simply press the button to cycle through all the LED color options and patterns. In addition this ESC is a distribution board for 4x more sets of LEDS that you can solder on to place on your drone's arms. All of the connected LEDs will by in sync with the on-board controller making it super simple for you. Changing all the LED colors on your drone is now as easy as a press of a button! (13 pre-programmed colors and patterns)

Not only does it have on-board LEDs, but the Razor LED ESC acts as it's own LED distribution board too! Hook up to 4 additional RGB LED strips for a super bright and colorful quad. The best part is the Razor LED ESC has an built in 5v regulator that powers all the LEDs for you in addition to sending the signal to each LED with the pre-programmed settings. All you have to do is press the button to cycle through all the cool effects.


  • Specifications
    • Input: 2-6s LiPoly
    • Constant: 55 Amps
    • Burst: 65 Amps
    • Dimensions: 39x45x5mm
    • Mounting holes: 30.5x30.5 M4 (M3 with rubber inserts)
    • Signal wire: 7cm
    • Weight: 15g
    • 8pin connector pinout: VBAT, Ground, Current ADC, TLM, Motor 1, Motor 2, Motor 3, Motor 4
    Includes
    • 1x Lumenier Razor LED 55A 4in1 F3 BLHeli_32 2-6s ESC
    • 1x 8pin micro JST-SH 7cm connector for 4in1 ESC to FC connection
    • 1x 2200uF 35V Capacitor4x M3 Anti-vibration gummies (extra)
  • Features
    • New F3 MCU running at 108MHz, (older ESCs use F0 at 48MHz)
    • Latest Gen. firmware using BLHeli_32 (Razor_32 target)
    • Supports DSHOT 1200, Proshot, Oneshot125 (125-250us), Oneshot42(41.7-83.3us) and Multishot (5-25us). Auto-detection.
    • Onboard RGB LEDs with controller and button + LED distribution system
    • Built in 5v regulator that powers the LED system
    • Adaptive timing, compatible with a wide range of motors and Kv
    • Synchronous rectification technology adds efficiency, damped light
    • Powerful regenerative braking / active braking.
    • 2-6s LiPo battery compatible
Lumenier Micro Razor 4in1 20x20 F3 BLHeli_32 30A 2-6s ESC

Lumenier Micro Razor 4in1 20x20 F3 BLHeli_32 30A 2-6s ESC

The small and powerful Lumenier Micro Razor 4in1 20x20 F3 BLHeli_32 30A 2-6s ESC. The perfect 4in1 ESC for micro builds and light weight full size quads.

The Lumenier Micro Razor F3 BLHeli_32 30A 2-6s ESC is a 32bit ESC running the latest gen. BLHeli_32 firmware, and featuring a future proof powerful F3 processors. Now 4 of these ESCs combine to have more processing power than your whole flight controller! The 32bit architecture enables the ESC to run at incredible speeds resulting in better performance, faster input signals and lower latency compared to older 8bit ESCs. This ESC also features a live telemetry connection for more advanced flight controllers, as well as a top of the line current sensor.

One of the biggest features of the Lumenier Razor ESC is the incredibly tiny size for such a powerful ESC. Coming in at only 7.5g and 32mm wide and 35mm in length, it will work perfectly on tight builds of modern day racing drones. Up to 30A of constant power in just a 7.5g package. If you are looking for an ESC that is built to be the best and have all the latest features of BLHeli_32, then the Lumenier Micro Razor 4-in-1ESC is the perfect match for you.


  • Specifications
    • Input: 2-6s LiPoly
    • Constant: 30 Amps
    • Burst: 40 Amps
    • Dimensions: 32x36x5mm
    • Mounting holes: 20x20 M3
    • Signal wire: 7cm
    • Weight: 7.5g
    • 8pin connector pinout: VBAT, Ground, Current ADC, TLM, Motor 1, Motor 2, Motor 3, Motor 4
    Includes
    • 1x Lumenier Micro Razor 4in1 20x20 F3 BLHeli_32 30A 2-6s ESC
    • 1x 35V 1000uF LOW ESR Capacitor
    • 1x 8pin micro JST-SH 7cm connector for 4in1 ESC to FC connection
    • 4x M3 rubber o-rings
  • Features
    • New F3 MCU running at 108MHz, (older ESCs use F0 at 48MHz)
    • Latest Gen. firmware using BLHeli_32 (Razor_32 target)
    • Supports DSHOT 1200, Proshot, Oneshot125 (125-250us), Oneshot42(41.7-83.3us) and Multishot (5-25us). Auto-detection.
    • Ultra-Lightweight (7.5g), and compact size
    • Adaptive timing, compatible with a wide range of motors and Kv
    • Sychronous rectification technology adds efficiency, damped light
    • Powerful regenerative braking / active braking.
    • 2-6s LiPo battery compatible
Lumenier Razor F3 BLHeli_32 30A 2-6s ESC
NEW PRODUCT

Lumenier Razor F3 BLHeli_32 30A 2-6s ESC

The highly advanced Lumenier Razor F3 BLHeli_32 30A 2-6s ESC. A small premium ESC packed full of features like RGB LED, current sensor, high amperage FETs, telemetry and more.


Lumenier Razor Pro F3 BLHeli_32 45A 2-6s ESC
NEW PRODUCT

Lumenier Razor Pro F3 BLHeli_32 45A 2-6s ESC

The highly advanced Lumenier Razor Pro F3 BLHeli_32 45A 2-6s ESC. A small premium ESC packed full of features like RGB LED, current sensor, high amperage FETs, telemetry and more.


Lumenier 12 amp ESC w/ SimonK AutoShot (2-4s N-FET)

Lumenier 12 amp ESC w/ SimonK AutoShot (2-4s N-FET)

The Lumenier 12 amp ESC with customized SimonK firmware including OneShot auto-detect and Active Braking/Damped Light/Comp_PWM is the perfect ESC to use on mini FPV quads such as the QAV250. This ESC comes pre-loaded with the newest firmware compatible with new features like "OneShot" (no soldering required, it will auto-detect if OneShot is enabled), Complimentary PWM (similar to KISS braking feature), compatible with all Lumenier motors up to 4 cell.

The Lumenier 12 amp AutoShot ESC have been tested and are compatible with all Lumenier motors (FX1806, FX2206, FXC2206), 2S-4S, both 5" and 6" props without sync loss issues or cogging.


  • Specifications
    • Max continuous load: ~12 amps
    • Burst Current: 22A/10sec
    • BEC: 5v/1amp max
    • Lipo Cells: 2 to 4 cells
    • Cables are fitted with female 2mm bullet connectors
    • Weight: 10g
    • N-FET only with BEC flashed with SimonK firmware
    Dimensions
    • 31mm L x 18mm W x 7mm H (35mm in length including capacitor)
    • 15cm signal wire / 5v power
    • 5cm motor wires (including 2mm bullet connector)
    • 70cm ESC power wires
  • Features
    • Active Braking / Damped Light / Comp_PWM
    • AutoShot (OneShot125 / FastPWM Auto Detect)
    • Customized to drive all motors without sync issues or cogging.
Lumenier 30 amp ESC w/ SimonK AutoShot Firmware

Lumenier 30 amp ESC w/ SimonK AutoShot Firmware

Jointly developed with SimonK himself, this is Lumenier's rendition of the popular 30amp "F-30" ESC with SimonK firmware - The Lumenier Mini 30 amp ESC with customized SimonK firmware including OneShot auto-detect is the perfect ESC to use on mini FPV quads such as the QAV250. This ESC is small in size (51x25x10mm) and big on power, supporting 30A on 4s. The ESC comes pre-loaded with the newest firmware, which is compatible with new features like "OneShot" (it will auto-detect if OneShot is enabled), Comp PWM (similar to KISS braking feature), compatible with all Lumenier motors up to 4 cell.

Simon had this to say about the new Lumenier SimonK ESCs:

"These ESCs are a revision of the nearly-perfect F-30A ESCs with high-quality board layout and components."

These ESCs are some of the most-recommended ESCs for multirotor use (with modified software) due to their reliability and capability for such a reasonable price. However, the original software intended for use in planes and helicopters requires a low-pass stage in the motor timing sense circuitry. This filter helps the stock firmware deal with PWM noise when sensing the timing, but lags the signal and is detrimental in some cases. With SimonK multirotor-specific firmware preloaded, and this analog filtering removed, the required noise filtering is done in software. The result is that timing synchronization loss from motor saturation during extreme instantaneous acceleration becomes avoidable, and start-up of higher-inductance motors is much smoother.

With the firmware preloaded, there is no need to play around with ESC settings to disable low-voltage shutdown or to change the timing to improve compatibility with pancake-style motors. Motors of all shapes and sizes should work providing they do not overload the ESC. In the event that a future motor does cause problems, the firmware allows for updates via a USB linker or by normal ISP methods, and is compatible with the normal bs_nfet.hex target.


  • Specifications
    • Max continuous load: ~23 amps
    • BEC: 5v/3amps max
    • Lipo Cells: 2 to 4 cells
    • Bare cables without bullet connectors
Lumenier 20 amp ESC w/ SimonK AutoShot Firmware

Lumenier 20 amp ESC w/ SimonK AutoShot Firmware

The Lumenier Mini 20 amp ESC with customized SimonK firmware including OneShot auto-detect is the perfect ESC to use on mini FPV quads such as the QAV250. This ESC is small in size (27x14.5x6mm) and big on power, supporting 20A on 4s. The ESC comes pre-loaded with the newest firmware, which is compatible with new features like "OneShot" (no soldering required, it will auto-detect if OneShot is enabled), Comp PWM (similar to KISS braking feature), compatible with all Lumenier motors up to 4 cell.


Lumenier Mini BLHeli ESCs

Lumenier Mini BLHeli ESCs

The Lumenier mini BLHeli ESCs are top performing electronic speed controllers with fast mosfet driven, dedicated driver chips on a quality PCB. This gives superior braking and freewheeling performance. The motor braking exceptionally fast thanks to the Silabs processor along with high quality gate drivers. The Lumenier BLHeli ESCs are signal wire programmable with an Arduino Nano v3 board, or other Silab programmers that are compatible with the BLHeli bootloader.


CAGE Code: 84VM0
Copyright © 2022 Lumenier. All Rights Reserved.
NOTION Design Group