Electronics

Lumenier Mini Razor Pro 4in1 20x20 F3 BLHeli_32 45A 2-6s ESC

The Lumenier Mini Razor F3 BLHeli_32 45A 2-6s ESC is a 32bit ESC running the latest gen. BLHeli_32 firmware, and featuring a future proof powerful F3 processors. Now 4 of these ESCs combine to have more processing power than your whole flight controller! The 32bit architecture enables the ESC to run at incredible speeds resulting in better performance, faster input signals and lower latency compared to older 8bit ESCs. This ESC also features a live telemetry connection for more advanced flight controllers, as well as a top of the line current sensor.

The Mini Razor Pro was designed for the drone pilot who loves the tiny 20x20 form factor but also wants to squeeze out every ounce of juice out of their equipment as possible. While the entire ESC is wider than the mounting holes, many frames have extra spillover space on the sides, so the additional width isn't an issue. Using this ESC allows you to still use your favorite 20x20 F7 FC while not worrying about putting too much stress on a lower-rated ESC. The Mini Razor Pro has 45A of continuous support that will give you the peace of mind to push your quad to the limit!

The Mini Razor Pro's innovative modular power system gives the user the option to install one of three different modules that give the 4-in-1 ESC additional functionality related to power management. Choose either the power filter module, extra capacitance module, or voltage regulator module to make your Mini Razor Pro fit to your specific needs (modules sold separately).

Lumenier Razor LED 55A 4-in-1 F3 BLHeli_32 2-6s ESC

The Lumenier Razor LED 55A 4in1 F3 BLHeli_32 2-6s ESC is a 32bit ESC running the latest gen. BLHeli_32 firmware, and featuring future proof powerful F3 processors. Now 4 of these ESCs combine to have more processing power than your whole flight controller! The 32bit architecture enables the ESC to run at incredible speeds resulting in better performance, faster input signals and lower latency compared to older 8bit ESCs. This ESC also features a live telemetry connection for more advanced flight controllers, as well as a top of the line current sensor.

The Lumenier Razor LED ESC also includes 4x onboard RGB LEDs with a pre-programmed controller chip with an easy-press button. Simply press the button to cycle through all the LED color options and patterns. In addition this ESC is a distribution board for 4x more sets of LEDS that you can solder on to place on your drone's arms. All of the connected LEDs will by in sync with the on-board controller making it super simple for you. Changing all the LED colors on your drone is now as easy as a press of a button! (13 pre-programmed colors and patterns)

Not only does it have on-board LEDs, but the Razor LED ESC acts as it's own LED distribution board too! Hook up to 4 additional RGB LED strips for a super bright and colorful quad. The best part is the Razor LED ESC has an built in 5v regulator that powers all the LEDs for you in addition to sending the signal to each LED with the pre-programmed settings. All you have to do is press the button to cycle through all the cool effects.

Lumenier LUX HD Lite F7 Flight Controller

The Lumenier LUX HD Lite F7 Flight Controller is DJI HD System Ready with an on-board 9v regulator to power the DJI Air Unit in a simple plug and play configuration. It uses a powerful F7 processor along with top of the line hardware. Unleash the capabilities of your FPV Racing Quadcopter with the Lumenier LUX HD Lite F7 Flight Controller. This LUX HD Lite F7 comes in a standard 30.5x3.5 form factor weighing only 7g! The bottom of the FC is also completely flat without any components, making it super low profile and easy to stack above a 4in1 ESC for example.

The LUX HD Lite F7 builds on all the best features of its predecessors and further improves on hardware components and layout, and now dedicated with a design for the DJI digital HD system. You get a whopping 6x dedicated UART ports with built-in inversion for peripherals, along with built in 128Mbit 16MB flash memory for Blackbox recording. This "Lite" version removes the analog OSD overlay chip saving space and weight since it is not needed for the DJI digital system. However all the data is still there and can be passed via the digital link to display in your goggles. The telemetry link will show you important information on your digital FPV display like battery voltage, flight time, warnings, RSSI, smart audio features and more.

This Flight Controller feature 2 on-board LC VBAT filtered power pads designed to power your DJI Air Unit at 9v and also other 5v accessories. The onboard 5v 3A regulator can be used to power the camera, Rx, and LEDs all at the same time, while the dedicated 9v 2A regulator reliably powers the DJI Air Unit or Vista system.

Lumenier Mini 4Power + Plus PDB (20x20mm, 5v/8v Reg, 100A Curr.)

The Lumenier Mini 4Power + Plus PDB is a feature rich power distribution board designed for mini quadcopters. The board uses 20x20mm mounting hole pattern (perfect for small builds) to easily fit up to most airframes. This PDB features an easy to solder layout keeping builds clean and simple. The Mini 4Power + Plus has all your power needs in one place with an onboard 5v and 8v BEC as well as a 100A capable Current Sensor. It can support from 3-5s LiPo battery and includes a XT30 plug for your build. Alternatively, you can simply solder power wires directly to the PDB and secure it in place, reducing stress on the solder point. Each voltage regulator can supply up to 2A of current, allowing them to easily power your VTX, camera, FC, and some LEDs.

Lumenier 4Power + Plus PDB (5v/10v Reg, 184A Curr.)

The Lumenier 4Power + Plus PDB is a feature rich power distribution board designed for small quadcopters. The board uses the standard 30.5mm mounting hole pattern (common to most flight controllers) to easily fit up to most airframes. This PDB features an easy to solder layout keeping builds clean and simple. The 4Power + Plus has all your power needs in one place with an onboard 5v and 10v BEC as well as a 184A capable Current Sensor. It can support from 3-6s LiPo battery and includes a lay-flat XT60 plug for low profile builds. Alternatively, you can simply solder power wires directly to the PDB and use a cable tie to secure it in place, reducing stress on the solder point. Each voltage regulator can supply up to 2A of current, allowing them to easily power your VTX, camera, FC, and some LEDs.

Lumenier MICRO LUX V2 - F4 Flight Controller + OSD

The Lumenier MICRO LUX V2 F4 Flight Controller with OSD brings incredible power and performance to the micro brushless world. It uses a powerful F4 processor along with top of the line hardware. Now you can get all the performance from an F4 based flight controller in a micro size! The V2 now includes an on-board Betaflight OSD. Using an On Screen Display has never been simpler, just drag and drop in the Betaflight Configurator. This flight controller uses 20x20mm mounting holes and a low profile design allowing for smaller airframe designs than ever before. The MICRO LUX V2 comes with BetaFlight pre-installed.

The MICRO LUX supports both SBUS and PPM inputs as well as DSM/DSMX receivers with both 5v and 3.3v support.

Lumenier™ and LUX™ are registered trademarks of Lumenier.

Lumenier SKITZO Flight Controller Powered by RaceFlight

The Lumenier SKITZO Flight Controller Powered by RaceFlight is the most advanced, performance driven, flight controller ever designed. The SKITZO Flight Controller was created in collaboration with and named after the flow master himself SKITZO FPV. Capable of running 32kHz gyro sample rate, PID loop, motor loop and processing all calculations in real time. The SKITZO FC is powered by the same hardware as the new RaceFlight Revolt which has incredible performance. The Lumenier SKITZO Flight Controller uses a F405 MPU and a Invensense 20602 gyro in combination with RaceFlight software to give you the BEST performance possible. This gyro is by far the most noise free and accurate gyro available.

Lumenier 12 amp ESC w/ SimonK AutoShot (2-4s N-FET)

The Lumenier 12 amp ESC with customized SimonK firmware including OneShot auto-detect and Active Braking/Damped Light/Comp_PWM is the perfect ESC to use on mini FPV quads such as the QAV250. This ESC comes pre-loaded with the newest firmware compatible with new features like "OneShot" (no soldering required, it will auto-detect if OneShot is enabled), Complimentary PWM (similar to KISS braking feature), compatible with all Lumenier motors up to 4 cell.

The Lumenier 12 amp AutoShot ESC have been tested and are compatible with all Lumenier motors (FX1806, FX2206, FXC2206), 2S-4S, both 5" and 6" props without sync loss issues or cogging.

Lumenier F4 AIO Flight Controller

The Lumenier F4 AIO Flight Controller combines a STM32F4 MCU, Betaflight OSD, full PDB, 12v 3A and 5v 3A BEC, Current Sensor, all in 1 compact package and weighing only 10g! Like other Betaflight OSD enabled flight controllers, you’ll be able to tune your PID’s using your transmitter and use the drag and drop OSD setup in the OSD tab of the BetaFlight Configurator.

Lumenier 30 amp ESC w/ SimonK AutoShot Firmware

Jointly developed with SimonK himself, this is Lumenier's rendition of the popular 30amp "F-30" ESC with SimonK firmware - The Lumenier Mini 30 amp ESC with customized SimonK firmware including OneShot auto-detect is the perfect ESC to use on mini FPV quads such as the QAV250. This ESC is small in size (51x25x10mm) and big on power, supporting 30A on 4s. The ESC comes pre-loaded with the newest firmware, which is compatible with new features like "OneShot" (it will auto-detect if OneShot is enabled), Comp PWM (similar to KISS braking feature), compatible with all Lumenier motors up to 4 cell.

Simon had this to say about the new Lumenier SimonK ESCs:

"These ESCs are a revision of the nearly-perfect F-30A ESCs with high-quality board layout and components."

These ESCs are some of the most-recommended ESCs for multirotor use (with modified software) due to their reliability and capability for such a reasonable price. However, the original software intended for use in planes and helicopters requires a low-pass stage in the motor timing sense circuitry. This filter helps the stock firmware deal with PWM noise when sensing the timing, but lags the signal and is detrimental in some cases. With SimonK multirotor-specific firmware preloaded, and this analog filtering removed, the required noise filtering is done in software. The result is that timing synchronization loss from motor saturation during extreme instantaneous acceleration becomes avoidable, and start-up of higher-inductance motors is much smoother.

With the firmware preloaded, there is no need to play around with ESC settings to disable low-voltage shutdown or to change the timing to improve compatibility with pancake-style motors. Motors of all shapes and sizes should work providing they do not overload the ESC. In the event that a future motor does cause problems, the firmware allows for updates via a USB linker or by normal ISP methods, and is compatible with the normal bs_nfet.hex target.

Lumenier 20 amp ESC w/ SimonK AutoShot Firmware

The Lumenier Mini 20 amp ESC with customized SimonK firmware including OneShot auto-detect is the perfect ESC to use on mini FPV quads such as the QAV250. This ESC is small in size (27x14.5x6mm) and big on power, supporting 20A on 4s. The ESC comes pre-loaded with the newest firmware, which is compatible with new features like "OneShot" (no soldering required, it will auto-detect if OneShot is enabled), Comp PWM (similar to KISS braking feature), compatible with all Lumenier motors up to 4 cell.

Lumenier Mini BLHeli ESCs

The Lumenier mini BLHeli ESCs are top performing electronic speed controllers with fast mosfet driven, dedicated driver chips on a quality PCB. This gives superior braking and freewheeling performance. The motor braking exceptionally fast thanks to the Silabs processor along with high quality gate drivers. The Lumenier BLHeli ESCs are signal wire programmable with an Arduino Nano v3 board, or other Silab programmers that are compatible with the BLHeli bootloader.

Lumenier LUX V2

The Lumenier LUX V2 flight controller is the next generation of the popular Lumenier LUX. It uses a powerful F3 processor along with top of the line hardware. Unleash the capabilities of your FPV Racing Quadcopter with the Lumenier LUX Flight Controller. Achieve gyro refresh rates up to 8kHz (high speed SPI) using popular Betaflight, CleanFlight and RaceFlight firmware along with ultra low looptimes. The LUX comes with BetaFlight pre-installed.

The LUX V2 builds on all the best features of the V1 board and further improves on hardware components and layout. Now you get a whopping 5x dedicated UART ports for periphials, along with an SD Card slot for practically unlimited data logging. The MPU has also been updated to the low noise MPU6000 Gyro making tuning even easier. No longer do you need to solder jumper pads for PPM/SBUS selection, it is automatically chosen via software! The powerful F3 MCU also supports the latest DSHOT protocol available in the newest BetaFlight firmware.

The Lumenier LUX is a very low profile board allowing it to be mounted in a variety of ways. The board also comes with a set of pin headers you can optionally solder on. Alternatively, signal wires can be soldered directly to the pads to save on size and weight. The LUX supports PPM or Serial RX (including Futaba, FrSky, S.BUS, DSMX). A signal inverter is already included for S.BUS. Please note: PWM input for individual channels is not supported.