Flight Controllers

lumenier-lux-v2-flight-controller Lumenier LUX V2

The Lumenier LUX V2 flight controller is the next generation of the popular Lumenier LUX. It uses a powerful F3 processor along with top of the line hardware. Unleash the capabilities of your FPV Racing Quadcopter with the Lumenier LUX Flight Controller. Achieve gyro refresh rates up to 8kHz (high speed SPI) using popular Betaflight, CleanFlight and RaceFlight firmware along with ultra low looptimes. The LUX comes with BetaFlight pre-installed.

The LUX V2 builds on all the best features of the V1 board and further improves on hardware components and layout. Now you get a whopping 5x dedicated UART ports for periphials, along with an SD Card slot for practically unlimited data logging. The MPU has also been updated to the low noise MPU6000 Gyro making tuning even easier. No longer do you need to solder jumper pads for PPM/SBUS selection, it is automatically chosen via software! The powerful F3 MCU also supports the latest DSHOT protocol available in the newest BetaFlight firmware.

The Lumenier LUX is a very low profile board allowing it to be mounted in a variety of ways. The board also comes with a set of pin headers you can optionally solder on. Alternatively, signal wires can be soldered directly to the pads to save on size and weight. The LUX supports PPM or Serial RX (including Futaba, FrSky, S.BUS, DSMX). A signal inverter is already included for S.BUS. Please note: PWM input for individual channels is not supported. 

 Buy Now

Hardware Features

  • New in V2
    • Dedicated UART for RC RX use, no need to solder a jumper to select PPM/SRX anymore.
    • Dedicated telemetry UART, this brings the total to 5x plus USB.
    • SD Card slot for BlackBox data recording (SD card not included)
    • Low noise MPU6000 SPI Gyro.
    • USB detection can disable things like buzzer when configuring on the bench.
    • New ultra low noise regulators for MCU and IMU power systems.
  • USB Conflict resolution - Hardware inversion, SBUS or telemetry can be used on any of the 3 available hardware serial ports. USB will not interfere with peripherals.
  • High Speed SPI 8kHz Gyro
  • MPU interrupt connected to F3, allowing the F3 to know immediately when fresh data is available.
  • Dedicated Boot button for easy firmware flashing.
  • Reinforced solder pads for trouble-free direct soldering.
  • Extremely low profile design.
  • Recessed, sideways pin headers. Also enables soldering of all wires directly to pads without use of any pin headers.
  • Integrated FRSky RSSI Filter (RC filter).
  • Input voltage 6v to 24v. Power the board directly from flight pack up to 6S (on 'BAT' pad only!).
  • VIN + VBAT merged - A single wire to power the board will provide voltage input and Telemetry/OSD voltage data.
  • Filtered voltage output - output 5v 1A (and 3.3v where applicable) to power peripherals such as GPS, RX, BLACKBOX, OSD. 5v/3.3v RX selectable.
  • Note: RX pad is dedicated to UART 4 in the Configurator.

lumenier-lux-v2-flight-controller-back Software/Hardware Features

  • Betaflight support (Supports new DSHOT protocol)
  • Cleanflight support (RACE target).
  • BLHeli passthrough flashing supported by hardware 
  • Raceflight ready

Specifications

  • STM32F303RCT6(256kB flash) 32-bit processor
  • MPU6000 SPI Gyro/Accelerometer
  • Micro SD memory card slot (SD card not included)
  • High quality, gold plated PCB
  • Highest quality components, individually sourced to meet Lumenier standards
  • Micro USB connector for programming
  • Dimensions: 36x36x6mm (includes USB in height)
  • Mounting Holes: 30.5mm square to center of holes 
  • Weight: 5g

Includes

  • 1x Lumenier Lux V2 Flight Controller
  • 2x 2x7 Straight Pin Headers

Downloads

Videos

Joshua Bardwell Review

 Buy Now


lumenier-f4-aio-flight-controller Lumenier F4 AIO Flight Controller

The Lumenier F4 AIO Flight Controller combines a STM32F4 MCU, Betaflight OSD, full PDB, 12v 3A and 5v 3A BEC, Current Sensor, all in 1 compact package and weighing only 10g! Like other Betaflight OSD enabled flight controllers, you’ll be able to tune your PID’s using your transmitter and use the drag and drop OSD setup in the OSD tab of the BetaFlight Configurator. 

Features

  • STM32F4 MCU (Spi connected to Gyro)
  • Built in PDB for direct connect of ESC power and signal wires
  • Built in high current bar
  • Direct battery connect 3-6S with filtered Output of 5v 3A, 12v 3A
  • SBUS/PPM + DSMX Ports
  • SPI Gyro MPU6000
  • On-Board Drag and Drop OSD (controlled by BetaFlight, FC over SPI bus)
  • Onboard SD Memory for Blackbox
  • Built-in Current Sensor (~140A)
  • 3x UART
  • Buzzer output
  • WS2812B LED output

lumenier-f4-aio-flight-controller-parts Specifications

  • Mounting holes: 30.5 x 30.5mm
  • Target: LUXF4OSD in BF 3.2+
  • Firmware: Betaflight
  • Weight:10g 

Includes

  • 1x Lumenier F4 AIO Flight Controller
  • 1x XT60 flat mount power connector
  • 1x Set of nylon spacers (5mm and 3mm), screws and nuts

 Buy the Lumenier F4 AIO Flight Controller


Lumenier SKITZO Flight Controller Powered by RaceFlight

lumenier-skitzo-raceflight-flight-controller-back

The Lumenier SKITZO Flight Controller Powered by RaceFlight is the most advanced, performance driven, flight controller ever designed. The SKITZO Flight Controller was created in collaboration with and named after the flow master himself SKITZO FPV. Capable of running 32kHz gyro sample rate, PID loop, motor loop and processing all calculations in real time. The SKITZO FC is powered by the same hardware as the new RaceFlight Revolt which has incredible performance. The Lumenier SKITZO Flight Controller uses a F405 MPU and a Invensense 20602 gyro in combination with RaceFlight software to give you the BEST performance possible. This gyro is by far the most noise free and accurate gyro available.

 Buy the SKITZO Flight Controller Powered by RaceFlight

 


lumenier-micro-lux-v2-front Lumenier MICRO LUX V2 - F4 Flight Controller + OSD

The Lumenier MICRO LUX V2 F4 Flight Controller with OSD brings incredible power and performance to the micro brushless world. It uses a powerful F4 processor along with top of the line hardware. Now you can get all the performance from an F4 based flight controller in a micro size! The V2 now includes an on-board Betaflight OSD. Using an On Screen Display has never been simpler, just drag and drop in the Betaflight Configurator. This flight controller uses 20x20mm mounting holes and a low profile design allowing for smaller airframe designs than ever before. The MICRO LUX V2 comes with BetaFlight pre-installed.

The MICRO LUX supports both SBUS and PPM inputs as well as DSM/DSMX receivers with both 5v and 3.3v support.

micro-lux-v2-diagram-top

Software/Hardware Features

  • 2-4S Direct Lipo input support (5-16v)
  • On-board BetaFlight OSD
  • On-board 5v/2A and 3.3v/0.2A regulators
  • SBUS and PPM support
  • RGB LED dedicated pad, Current Sensor pad and Buzzer Pad
  • VBAT Monitoring support
  • 3x UART Ports
  • Betaflight support (Supports new DSHOT protocol)
  • BLHeli passthrough flashing supported by hardware

Specifications

  • STM32F405 (2MB flash) 32-bit processor
  • MPU6000 Gyro/Accelerometer
  • High quality 1.6mm PCB
  • Micro USB connector for programming
  • Dimensions: 27x27x6mm (includes USB in height)
  • Mounting Holes: 20mm square to center of holes 
  • Weight: 4g

Includes

  • 1x Lumenier MICRO Lux V2 F4 Flight Controller w/ OSD
  • 1x Set of plastic 5mm and 3mm standoffs + screws / nuts

Optional Recommendations

We suggest the following gear to complete your micro brushless build. (Not included)

Downloads

lumenier-micro-lux-v2-size

 Buy MICRO LUX V2 F4 Flight Controller


Lumenier™ and LUX™ are registered trademarks of Lumenier.