Brushless ESC

Lumenier Mini BLHeli ESCs

lumenier-30-amp-blheli-lead The Lumenier mini BLHeli ESCs are top performing electronic speed controllers with fast mosfet driven, dedicated driver chips on a quality PCB. This gives superior braking and freewheeling performance. The motor braking exceptionally fast thanks to the Silabs processor along with high quality gate drivers. The Lumenier BLHeli ESCs are signal wire programmable with an Arduino Nano v3 board, or other Silab programmers that are compatible with the BLHeli bootloader.

Buy the 20amp BLHeli ESC Buy the 30amp BLHeli ESC

Lumenier ESCs w/ SimonK AutoShot Firmware

lumenier-20amp-autoshot-2-4s-close The Lumenier Mini 20 amp ESC with customized SimonK firmware including OneShot auto-detect is the perfect ESC to use on mini FPV quads such as the QAV250. This ESC is small in size (27x14.5x6mm) and big on power, supporting 20A on 4s. The ESC comes pre-loaded with the newest firmware, which is compatible with new features like "OneShot" (no soldering required, it will auto-detect if OneShot is enabled), Comp PWM (similar to KISS braking feature), compatible with all Lumenier motors up to 4 cell.

 

Buy the 20amp SimonK ESC

 

lumenier-simonk-esc-close Jointly developed with SimonK himself, this is Lumenier's rendition of the popular 30amp "F-30" ESC with SimonK firmware - The Lumenier Mini 30 amp ESC with customized SimonK firmware including OneShot auto-detect is the perfect ESC to use on mini FPV quads such as the QAV250. This ESC is small in size (51x25x10mm) and big on power, supporting 30A on 4s. The ESC comes pre-loaded with the newest firmware, which is compatible with new features like "OneShot" (it will auto-detect if OneShot is enabled), Comp PWM (similar to KISS braking feature), compatible with all Lumenier motors up to 4 cell.

Simon had this to say about the new Lumenier SimonK ESCs:

These ESCs are a revision of the nearly-perfect F-30A ESCs with high quality board layout and components.

These ESCs are some of the most-recommended ESCs for multirotor use (with modified software) due to their reliability and capability for such a reasonable price. However, the original software intended for use in planes and helicopters requires a low-pass stage in the motor timing sense circuitry. This filter helps the stock firmware deal with PWM noise when sensing the timing, but lags the signal and is detrimental in some cases. With SimonK multirotor-specific firmware preloaded, and this analog filtering removed, the required noise filtering is done in software. The result is that timing synchronization loss from motor saturation during extreme instantaneous acceleration becomes avoidable, and start-up of higher-inductance motors is much smoother.

lumenier-simonk-esc With the firmware preloaded, there is no need to play around with ESC settings to disable low-voltage shutdown or to change the timing to improve compatibility with pancake-style motors. Motors of all shapes and sizes should work providing they do not overload the ESC. In the event that a future motor does cause problems, the firmware allows for updates via a USB linker or by normal ISP methods, and is compatible with the normal bs_nfet.hex target.

Specifications

  • Max continuous load: ~23 amps
  • BEC: 5v/3amps max
  • Lipo Cells: 2 to 4 cells
  • Bare cables without bullet connectors

Buy the 30amp ESC

lumenier-simonk-esc

12amp-autoshot-lumenier Lumenier 12 amp ESC w/ SimonK AutoShot (2-4s N-FET)

The Lumenier 12 amp ESC with customized SimonK firmware including OneShot auto-detect and Active Braking/Damped Light/Comp_PWM is the perfect ESC to use on mini FPV quads such as the QAV250. This ESC comes pre-loaded with the newest firmware compatible with new features like "OneShot" (no soldering required, it will auto-detect if OneShot is enabled), Complimentary PWM (similar to KISS braking feature), compatible with all Lumenier motors up to 4 cell. 

The Lumenier 12 amp AutoShot ESC have been tested and are compatible with all Lumenier motors (FX1806, FX2206, FXC2206), 2S-4S, both 5" and 6" props without sync loss issues or cogging. 

Features:

  • Active Braking / Damped Light / Comp_PWM
  • AutoShot (OneShot125 / FastPWM Auto Detect)
  • Customized to drive all motors without sync issues or cogging.

Specifications

  • Max continuous load: ~12 amps
  • Burst Current: 22A/10sec
  • BEC: 5v/1amp max
  • Lipo Cells: 2 to 4 cells
  • Cables are fitted with female 2mm bullet connectors
  • Weight: 10g
  • N-FET only with BEC flashed with SimonK firmware

Dimensions

  • 31mm L x 18mm W x 7mm H (35mm in length including capacitor)
  • 15cm signal wire / 5v power
  • 5cm motor wires (including 2mm bullet connector)
  • 70cm ESC power wires

 

Buy the 12amp ESC